Search Results
88 results found:
You searched for:
IWVT voltage input wireless transmitter
£152.99
The IWVT Wireless Transmitter is a cost effective alternative to
traditional wiring that offers the advantages of a low-cost installation in
inaccessible and expensive installation environments.
It is easily paired to any of the range of IWR receivers - thus offering a
“plug and play” solution to your analog voltage application.
The IWVT sensor should be used with any of the IWR range of receivers.
A line-of-sight range of up to 500 m is possible depending on the
wireless receiver used (refer to specific receiver datasheets for further
information).
Dualcon-3 Dual Output Isolating signal Converter
£275.31
The Dualcon-3 is a dual output isolating signal converter with full 3-Port isolation.
The Dualcon-3 signal isolator can accept virtually any input including 4-20mA loops, voltage inputs, thermocouples, PT100 sensors and potentiometers and provide an isolated 4-20mA or Voltage output.
The Dualcon-6 is also available if a DC power supply is required.
£184.51
The TC-TC is a Thermocouple Isolator which is used to isolate any thermocouple and provide an identical simulated thermocouple output.
Typically used to isolate thermocouples from input cards stopping any earth loop effects and eliminating any noise problems.
TC-TC-DUAL Thermocouple Isolator with 2 outputs
£275.31
The DCON-TCTC is a Thermocouple Isolator which is used to isolate any thermocouple and provide an identical simulated thermocouple output together with a second output which can also be a thermocouple output or a mA or Voltage output proportional to temperature.
The unit is typically used to isolate thermocouples from input cards stopping any earth loop effects and eliminating any noise problems.
Isocon-LIN Linearising Signal Converter
£184.51
The Isocon-LIN is a universal input DC powered signal converter which can linearise the output using up to 31 points of linearisation. The Isocon-LIN accepts virtually any input including 4-20mA loops, voltage inputs, thermocouples, PT100 sensors and potentiometers and provides an isolated linearised mA or Voltage output.
The Isocon-6 has a 12-36Vdc power supply and the Isocon-3 is also available if a AC power supply is required.
VCONHL-AC Ac Current or Voltage Input Isolating Signal Converter
£184.51
The VCONHL-AC is a 3-port isolating signal converter with an AC current or voltage input and an isolated 4-20mA or 0-10V output. Suitable inputs include 0-1A or 0-5A AC current signals from current transformers or AC voltage signals of up to 250Vrms.
DC current and voltage can also be converted into standard isolated 4-20mA or voltage outputs.
The unit measures the true RMS of the input waveform making the unit suitable for measuring waveforms from inverters or variable speed drives, as well as pure sine-wave inputs.
DIVIDER AC/DC Voltage Divider unit
£35.70
The II-DIVIDER unit is used to reduce AC or DC voltages to safe levels before inputting into our range of signal conditioning modules, typically the VCON-AC unit.
Isocon-AVE Averaging Signal Converter
£184.51
The Isocon-AVE is a universal input DC powered signal converter which can average the output over any time period from 1s to 60 seconds. The Isocon-AVE accepts virtually any input including 4-20mA loops, voltage inputs, thermocouples, PT100 sensors and potentiometers and provides an isolated averaged mA or Voltage output.
The Isocon-6 has a 12-36Vdc power supply and the Isocon-3 is also available if a AC power supply is required.
Isocon-DRIVE Isolating Signal Converterwith high current output
£184.51
The Isocon-DRIVE is a universal input DC powered signal converter which can output a high current output up to 125mA. The Isocon-DRIVE accepts virtually any input including 4-20mA loops, voltage inputs, thermocouples, PT100 sensors and potentiometers and provides a high current output or up to 0-125mA which can be used to drive outputs such as ballast controllers or control valves.
The Isocon-6 has a 12-36Vdc power supply and the Isocon-3 is also available if a AC power supply is required.
STRAIN Universal Strain Gauge Transmitter
£184.51
The STRAIN universal strain gauge transmitter can connect with almost any strain gauge, loadcell or pressure transducer and provides an isolated 4-20mA or voltage output.
Two versions are available, the STRAIN-6 with a 12-36Vdc supply or the STRAIN-3 with a 90-264 Vac supply
STRAIN-DUAL Universal Strain Gauge Transmitter with two outputs
£275.31
The STRAIN-DUAL universal strain gauge transmitter can connect with almost any strain gauge, loadcell or pressure transducer and provides two isolated 4-20mA or voltage outputs.
Two versions are available, the STRAIN-DUAL-6 with a 16-36Vdc supply or the STRAIN-DUAL-3 with a 90-264 Vac supply
Dualcon-AVE Dual Output converter with output averaging
£275.31
The Dualcon-AVE averaging signal isolator is a dual 4-20mA or 0-10V output DC powered isolating signal converter.
The Dualcon-AVE can accept virtually any input including 4-20mA loops, voltage inputs, thermocouples, PT100 sensors and potentiometers and provide two isolated 4-20mA or Voltage outputs which can be averaged over a time period from 1s to 60s.
The Dualcon-AVE-6 has a 16Vdc to 36Vdc supply and the Dualcon-AVE-3 is also available if a AC power supply is required.
£12.50
The II-ANT1000 is a 3dBi gain stubby antenna with a male SMA connector suitable for ZigBee and other 2.4GHz wireless networks.
It has a maximum power of 2W and its compact size but high gain make it suitable for battery powered sensors and low power routers.
FREQCON-IPWM Analogue to PWM Frequency Converter
£212.43
The FREQCON-IPWM converter accepts any type of process input and provides a PWM output.
This is typically used with units such as PLC's which don't have an analogue input but do have a PWM input.
Using the FREQCON-IPWM and thermocouple, RTD, current or voltage signal can be converted to a PWM output which can then be fed into the PLC or similar device.
£17.00
The II-ANT2000 is a 5dBi gain stubby antenna with a male SMA connector suitable for ZigBee and other 2.4GHz wireless networks.
It has a maximum power of 3W and its compact size but high gain make it suitable for battery powered sensors and low power routers.
FREQCON-PWMI PWM Frequency to Analogue Converter
£212.43
The FREQCON-PWMI converter can convert virtually any PWM type input into an isolated 4-20mA or Voltage output. Any frequency between 0 and 250kHZ can be converted and almost any input voltage level can be read.
£38.00
The II-ANT3000 is a 4dBi gain omni antenna with a male N Type connector suitable for ZigBee and other 2.4GHz wireless networks.
It has a maximum power of 20W and is protected to IP67 making it suitable for mounting outdoors.
£117.04
The 420TWHL loop powered isolator can replace standard DIN rail terminals to provide input isolation, signal conversion and RFI and noise rejection.
The isolators are a 2-wire device needing a 24Vdc supply on one terminal and returning a 4-20mA on the other.The input for the HL version can be configured for 4-20mA. 0-10V or similar, see the data sheet for all the variations available.
£54.00
The II-ANT4000 is a 6dBi gain omni antenna with a male N Type connector suitable for ZigBee and other 2.4GHz wireless networks.
It has a maximum power of 20W and is protected to IP67 making it suitable for mounting outdoors.
VOLTCON High Voltage Isolating Converter
£265.00
This range of isolated signal converters can accept a wide
range of AC and DC voltages and provide an isolated
4-20mA output.
The device uses a true RMS input stage which allows
accurate measurement of non-perfect AC waveforms.
The inputs of the device are connected directly to the power
rail to be measured and the outputs, which are always in the
range 4-20mA and proportional to the inputs, are connected
to the data acquisition equipment. The input voltage
measurements are totally isolated and protected with failsafe
resistor networks.
All units offer isolation between input and output, power and
input and power and output.
420TWRTD Loop Powered isolator
£117.04
The 420TWRTD can replace standard DIN rail terminals to provide input isolation, signal conversion and RFI and noise rejection.
The isolators are a 2-wire device needing a 24Vdc supply on one terminal and returning a 4-20mA on the other.The input for the RTD version can be configured for most 2 or 3 wire PT100 sensors and temperature ranges, see the data sheet for all the variations available.